Fish Fundamentals and Responsible Angling

This spring has been slow in the South Puget Sound for finding Sea-Run Cutthroat (SRC) Trout. Even my nearby beach, which tends to be prolific on an outgoing tide, has been barren this year. The last three times I was there I caught nothing, with not even a hit.

I was discussing that with the guys down at the Gig Harbor Fly Shop – and one of the guides mentioned that he’s noticed in the relatively few years he’s been around here that the SRC population appears to be much less than it used to be.

There may be many reasons for that; my opinion is that the fish are sensitive to the growing pressures on them from the urban and industrial pollution and runoff that surround Puget Sound. That is only going to get worse as the impacts of climate change bear down upon them – and us humans.

One may argue cause and effect, but one thing that seems inarguable is that anytime we come in contact with fish in our sport activities we should do whatever we can to protect them so we, and others, can continue to enjoy our sport.

Patagonia’s The Cleanest Line has an article by Andy J. Danylchuk, PhD on how to properly handle fish – whatever the species.

He recommends the usual practices: matching rod and line to the species; using a barbless hook; and keeping the fish in the water as much as possible.

Other recommendations may come as a surprise to those who have sought “hero shots” in the past. He recommends not lipping a fish (holding it by its lips) as that can put undo torsion on the head and vertebrae. Even holding a fish in a net (in the water) is to be avoided, as it’s a risk to the fish; much better to keep the fish totally submerged and use a forceps to reduce the hook.

Underwater cameras, as Andy points out, are becoming mainstream. One hopes the new ethic for fish handling and the “hero shot” is that of the fish kept totally submerged, underwater held only briefly until the shot is taken and the hook removed by a forceps.

The “new normal” may mean treating sport fisheries as the precious resource they are.

You can read the article here.

Fly Fishing and the Zen of Bathroom Fan Repair

Fly fishing and the repair of a bathroom exhaust fan may seem to be unrelated. But if fly fishing does present each of us with lessons for living a better life, then perhaps those same lessons can be applied to something as mundane as fixing a bathroom exhaust fan.

We have been having problems with the exhaust fan in our second floor hallway bath. First, the fan motor was replaced by an electrician as part of troubleshooting a problem with the timer that controls the fan’s operation; in addition to venting the bathroom, the fan operates on a daily cycle to ventilate the entire house (to reduce humidity and mold). Subsequent to the motor repair, we noticed the fan was running noticeably louder, to the point of increasing annoyance. This past weekend, I figured it was time to pull it out and see what was going on.

Of course, this would come after a morning trip down to the nearest beach (about 3 miles from my house) to fish for sea run cutthroat trout (SRC).

I got to the beach and started gearing up. I’ve gotten to where I understand this is part of the ritual and not something to be rushed. That putting on waders; stepping into wading boots; rigging up the rod; and finally tying on the fly – all are essential elements in reentering the world of fly and water.

Similarly, hours later when I was preparing to investigate the fan, I paused in the garage to assemble my tools. I first thought about what I was going to do. Then, I put the following into my tool bag: screwdrivers (both Phillips head and slot); needle-nose pliers; and some paper towels to wipe fan components. I also grabbed my small ladder that is handy for work inside the house.

When I got to the water, I started as always at the edge and made short casts. Nothing hit and after a few casts I made my way slowly into the water. With the falling tide, the tidal current was more like a river. Stepping carefully to maintain balance I continued blind casting, increasing the length of my casts to get to the seams out in the deeper water.

As I moved through the water I started to notice casting problems. Casts were falling short and my double hauls were not working as well as I would have liked. I stopped and took a deep breath. And it was clear: time to slow down and not rush my casts. That made all the difference.

After some work, I was on the ladder trying to put the fan into the box in the ceiling. The fan assembly is held in place by three screws and requires some careful work to hold the fan in place with one hand while trying to use the other hand to place the screw in a hole and tightening it. I was having problems and my body was tensing from frustration; with tight shoulders and sweat dripping into my eyes, the assembly dropped out several times.

And then I remembered how I slowed down and my casting improved. I set the assembly on top of the ladder, took a deep breath and stopped for a moment. I looked up toward the mounting holes. Rather than seeing than as problems I recognized they were just how the assembly mounted. I shook out my shoulders, took another deep breath, and mounted the assembly with only a few issues.

The day was getting warmer, the sun was shining on the falling water, and I wasn’t having much luck. I caught one sculpin, hooked one trout but it popped off the hook and saw what must have been a Coho jumping under the bridge. So I decided to call it a day.

I knew coming down to the beach it was probably not going to be a prolific day. August fishing is slow. Many fly fishers take the month off as the warmer water temperatures drive the fish off the beach into deeper waters. But I knew coming down it was more about getting into tidal water and watching the day start than about catching a dozen sea runs.

Similarly, after completing the repair on the fan, I realized the noise was caused by a dynamic imbalance in the plastic squirrel cage impeller. I did what I could and the noise had been reduced, but over time it will increase again, and that will mean having to go into the attic and replace the unit. But that will be after summer ends and the attic will be cooler.

And that in the end was the lesson for the day for both: acceptance of the situation.